Solutions

Start where the rework is.

Every car plant already measures rework per body, repaint rate, faults escaping to end of line, first-time-through and downtime minutes. Chassira lands on one of those numbers, on one process, with a baseline agreed in writing, and expands when it moves.

6 wedges1 process to startBaseline agreed in writing

run_41a9c2 · agent graph · plant BIW-2 · scenario 10 nodes · 1 approval gate
01 · orchestrator ingest.shift ✓ SUCCEEDED 02 · vehicle_line twin.simulate ✓ SUCCEEDED 03 · stamp_form stamp.form ✓ SUCCEEDED 04 · orchestrator approve.human ◆ APPROVAL 05 · weld_join weld.join ✓ SUCCEEDED 06 · frame_geometry frame.geometry ✓ SUCCEEDED 07 · paint_finish paint.finish ✓ SUCCEEDED 08 · powertrain_battery marriage.torque ✓ SUCCEEDED 09 · quality_anomaly inspect.fuse ✓ SUCCEEDED 10 · eol_calibrate eol.release ✓ SUCCEEDED

Illustrative scenario: Plant BIW-2 · EV crossover body shop to end of line · shift 1, one approval gate

By outcome

Six wedges, each with a metric the plant already has

The first paid pilot targets one of these. The metric column is what the pilot would be judged on.

Body shop

Weld lines and framing stations

Score every joint, catch expulsion and geometry debt as they form, propose the schedule for the engineer and correct framing inside the envelope. Metric: weld and geometry rework per body against the baseline.

Weld and joinFrame and geometry

Paint shop

Booths, ovens, inspection decks

Predict the defect map and set the booth ahead of it; localise what still appears to zone and condition. Metric: repaint rate and paint defects per body by type against the baseline.

Paint and finishQuality and anomaly

Pack and marriage

Battery and powertrain lines

Score every torque-to-yield trace and joining signal, hold the unit before a fault leaves the station, never touch the specification. Metric: faults caught before end of line and marriage rework.

Powertrain and battery

General assembly

Trim, torque, fill, glazing

Predict mis-torque, under-fill and glazing faults per vehicle and route or hold before end of line. Metric: torque and fill rework per vehicle and faults escaping to end of line.

Trim and fasten

End of line

Alignment, ADAS, leak, brake, roll, functional

Predict failures from the upstream build record and sequence retests inside takt; never write a verdict. Metric: first-time-through rate and retests per shift.

End of line and calibrate

Launch and takt

Whole plant

Rehearse the shift on the twin, optimise sequence, feeding and buffers against launch cadence, hold geometry and quality through the ramp. Metric: launch-ramp quality and takt adherence against the program plan.

Sequence and flowTwin
Where it pays

Four loops, four metrics

Chassira is not a dashboard. Each agent closes a loop a plant already measures in rework per body, repaint rate, faults escaping to end of line and downtime minutes. The tables show what each loop watches and what it is allowed to move.

Body shop

Catch the weld and the geometry before the body leaves framing

Servo-gun traces, seam vision and in-line measurement are fused at the cell into one estimate of joint quality and body geometry. Weld-and-Join proposes the schedule and sequence that hold crash-safety quality without geometry debt, the body-shop engineer approves, and Frame-and-Geometry corrects the framing station inside its envelope.

  • Joint quality scored per weld, not per destructive sample
  • Weld-schedule changes supervised by a named engineer
  • Framing corrections inside the qualified envelope, logged per body
agent.weld_join SUCCEEDED
Catch the weld and the geometry before the body leaves framing: signals watched and setpoints moved
SignalWatchesMoves
Weld current and forceServo-gun trace per jointSchedule proposal, under approval
ExpulsionTrace and seam visionCurrent and hold, under approval
Body dimensionIn-line measurementFraming offset inside the envelope
Paint shop

Set the booth before the defect, not the repaint after it

Booth temperature, humidity and airflow, film build and oven profiles are read per body and colour block. Paint-and-Finish predicts the defect map a body will carry and trims the booth inside the qualified window ahead of it; paint-defect vision localises what still appears to zone and condition.

  • Defects predicted from booth and chemistry state
  • Booth environment moved inside the qualified window
  • Every defect localised to zone, robot and condition
agent.paint_finish SUCCEEDED
Set the booth before the defect, not the repaint after it: signals watched and setpoints moved
SignalWatchesMoves
Booth environmentTemperature, humidity, airflow sensorsSetpoints inside the window
Film buildFilm-build gaugesFlash and cure profile
Dirt, runs, orange peelPaint-defect visionZone routing, spot-repair request
Pack and general assembly

Hold the unit before the torque fault leaves the station

Torque-to-yield traces, cell-to-pack joining signals, fill volumes and glazing vision are scored per fastener and per vehicle. Powertrain-and-Battery and Trim-and-Fasten hold and route units before a fault reaches end of line. Torque specifications and joint parameters are never written by an agent.

  • Every trace scored against the specification curve
  • Holds and routing, not parameter changes
  • Specifications locked read-only in the policy engine
agent.powertrain_battery SUCCEEDED
Hold the unit before the torque fault leaves the station: signals watched and setpoints moved
SignalWatchesMoves
Torque to yieldTool trace per fastenerUnit hold and routing
Pack integrityJoining, coolant and HV testsHold, proposal to engineer
Fluid fillVolume and pressureFill setpoints inside the window
End of line and takt

Prove the vehicle and hold the line

End-of-line results are fused with the upstream build record to predict failures before the stand sees them, and retests are sequenced inside takt. Sequence-and-Flow prices every sequence and buffer move in minutes and rework and optimises feeding and routing with cuOpt against launch cadence.

  • Failures predicted from upstream build data
  • Test verdicts and limits never written by an agent
  • Sequencing and buffers optimised, written inside agreed limits
agent.eol_calibrate SUCCEEDED
Prove the vehicle and hold the line: signals watched and setpoints moved
SignalWatchesMoves
ADAS calibrationTest-stand resultRetest sequencing
Alignment, leak, brake, rollTest-stand resultsRework routing
Takt and buffersMES, AGV and AMR stateSequence and buffer targets
Segments

Where plants start

Passenger-car OEM plants, light-truck plants, EV plants and startups, and tier-1 body, battery and module suppliers. Most plants pick one process and one wedge, prove the number, then expand.

Passenger-car OEM plantsLaunch cadence, first-time-through

Passenger-car OEM plants

Body, paint and general-assembly lines launching new models every year. The body-shop wedge first: weld-defect and gap-and-flush vision where rework is already counted.

Light-truck plantsMixed-material bodies, high takt

Light-truck plants

Aluminium and mixed-material joining, large panels and long general-assembly lines. Weld-and-Join and Frame-and-Geometry on the line with the most geometry rework.

EV plants and startupsNew battery lines, thin staffing

EV plants and startups

Cell-to-pack and cell-to-body lines standing up faster than engineers can staff them. Powertrain-and-Battery conformance on the marriage line first.

Tier-1 body, battery and module suppliersSupplier PPM, IATF traceability

Tier-1 body, battery and module suppliers

Body structures, battery modules and subassemblies delivered under IATF 16949 and customer PPM targets. Quality-and-Anomaly and conformance on the line that ships to the OEM.

Run timeline · scenario

One scenario shift, step by step

Every Chassira run is an ordered, inspectable sequence. This is run_41a9c2 on Plant BIW-2 · EV crossover body shop to end of line · shift 1. Scenario completes in 10 steps with one approval gate. Weld schedule change on robot W-14 approved by the body-shop launch engineer, framing offset held inside the envelope, booth humidity trimmed before the predicted dirt defects appeared, one pack held at marriage on a torque trace, and the shift released with full as-built records.

run_41a9c2 Plant BIW-2 · EV crossover body shop to end of line · shift 1 illustrative scenario SUCCEEDED
  1. 01 ingest.shift SUCCEEDED 0.8 s

    Plant Orchestrator · Pulled the shift build sequence, program control plan and qualified envelopes from MES: 412 bodies, four trim variants, weld schedule set W-rev 7, framing targets per station, paint colour blocks, torque specifications. Locked every safety-critical parameter as read-only.

  2. 02 twin.simulate SUCCEEDED 1 m 40 s

    Vehicle-and-Line Twin · Simulated 18 candidate weld-sequence, framing-offset and booth-window combinations on the plant twin, ranked on predicted body geometry, expulsion risk at robot W-14, paint defect map and takt against launch cadence.

  3. 03 stamp.form SUCCEEDED continuous

    Stamp-and-Form · Blank feed on press line P-3 adjusted by 0.4 mm and lubricant dose raised 3 percent for the new coil lot as springback risk on the rear door inner climbed. Panel dimension held inside the window; genealogy handed to framing.

  4. 04 approve.human APPROVAL 3 m 12 s

    Plant Orchestrator · Candidate #6 lowers weld current 2 percent and adds 20 ms hold on robot W-14 to cut predicted expulsion. Weld schedules are crash-safety critical and stay with a human, so the change was held for the body-shop launch engineer and approved at 06:14:52.

  5. 05 weld.join SUCCEEDED continuous

    Weld-and-Join · Approved schedule 7b applied on W-14. Current and force traces confirmed inside the window on the first 40 bodies; predicted expulsion risk fell from 0.31 to 0.06 and no geometry debt was introduced at the adjacent seams.

  6. 06 frame.geometry SUCCEEDED continuous

    Frame-and-Geometry · Framing station FS-1 offset corrected by 0.3 mm on the left B-pillar datum inside the qualified envelope as in-line measurement trended toward the tolerance edge. Gap-and-flush vision confirmed the correction on the next 25 bodies.

  7. 07 paint.finish SUCCEEDED continuous

    Paint-and-Finish · Booth B-2 humidity trimmed 2 points and airflow rebalanced for the dark-colour block as the defect model predicted dirt on horizontal panels. Film build held inside the window on the first colour block.

  8. 08 marriage.torque SUCCEEDED continuous

    Powertrain-and-Battery · Pack PK-1182 held at marriage after a torque-to-yield trace on fastener 7 fell outside the specification curve. Routed to rework with the trace attached; torque specification untouched, as always.

  9. 09 inspect.fuse SUCCEEDED continuous

    Quality-and-Anomaly · Gap-and-flush and paint-defect cameras, weld and torque traces and test results fused per body. Two paint dirt defects localised to booth B-2 zone 3 before the humidity trim took effect; both routed to spot repair, none escaped to final.

  10. 10 eol.release SUCCEEDED 2 m 05 s

    EOL-and-Calibrate · End of line proved alignment, ADAS calibration, leak, brake, roll and functional tests on every vehicle; two ADAS retests sequenced inside takt. Shift 1 released with as-built records, approvals and dispositions written for the quality lead.

Who it is for

Built for the people who run the plant

We have no customer quotes to show yet and will not invent any. These are the three roles in a car plant we build for, and the problems they bring to the first meeting.

Plant Manager or Manufacturing Director

Owns launch dates, takt, downtime, first-time-through, rework and cost.

What this person is dealing with today

  • Sampled inspection, andon reaction and siloed cell PLCs that let joint quality, geometry, paint and torque drift
  • Launch ramps where quality and takt collapse under new-model, EV and mixed-material complexity
  • A skilled process-engineer and technician shortage that cannot staff the localisation and EV launch wave

Body, Paint or Assembly Process (Launch) Engineer

Owns weld, paint and torque process windows, framing geometry, dimensional accuracy and launch quality.

What this person is dealing with today

  • Weld, rivet and adhesive parameter and sequence drift driving crash-safety joint defects, geometry loss and rework
  • Body-in-white dimensional and gap-and-flush error at framing costing downtime and warranty per body
  • Paint dirt, runs, orange peel and e-coat and film-build faults driving repaint, scrap and corrosion warranty

Quality, STA or Conformance Lead

Owns build quality, PPM, warranty and recall exposure, and IATF 16949, APQP and functional-safety traceability.

What this person is dealing with today

  • Torque, fluid-fill, battery-joint and ADAS-calibration faults escaping to the field as warranty and recall exposure
  • Stamping, body, paint, powertrain, battery, assembly and end of line siloed and reactive across the plant
  • Traceability evidence assembled by hand after the fact
Autonomy

Four levels, set per agent and per tag

A car plant does not go from manual to unattended in one step. Chassira makes the level explicit, auditable and reversible at any time. The first release runs shadow mode, then assist mode, then bounded autonomy on low-risk loops. Weld schedules stay supervised until the joint family is qualified, and torque specifications and test verdicts are never written by an agent.

Autonomy levels and the human role at each
LevelWhat the agent doesWhat the human doesWhere it sits in a pilot
L1 · ShadowReads weld, metrology, vision, torque, test, robot and MES signals; predicts and recommends; writes nothingRuns the line as today; compares predictions to audit and engineer outcomesDesign partners start here; the baseline is measured from the plant's own records
L2 · AssistProposes weld, framing, paint, routing, holding and sequencing moves with evidence, confidence, envelope and rollback pathApproves each action in the review consoleAssist mode: accuracy and ROI proven against the signed baseline
L3 · BoundedExecutes pre-approved low-risk actions: booth environment, framing offsets, blank feed and lubrication, routing, holds, sequencing, inside PLC and safety limits and the qualified envelopeApproves weld-schedule changes, torque-related decisions and vehicle releaseGraduated autonomy, after audited accuracy and ROI
L4 · ScaledSupervised weld-schedule adaptation for qualified joint families, across lines and plantsSets the envelope; reviews the shift record and evaluation resultsPlanned; after golden-dataset evaluation, twin validation and quality sign-off. Torque specifications and test verdicts never leave human hands
Pricing

Priced per process, per plant, per fleet

Land on one process with a measured baseline. Expand by process, plant and autonomy level. Outcome components are available on rework, downtime, warranty and first-time-through. Annual prepay carries a 15 to 20% discount.

Billing period
Process $18,000 per production process or area / month · billed monthly

Weld, paint or assembly control, or defect-inspection AI, for one process. For plants validating ROI on the wedge.

  • One process or area, one agent module
  • Plant-edge inference node included
  • Controller and sensor reads, guarded writes
  • Run log, audit trail, as-built record
  • Business-hours support
Start a pilot
Enterprise Custom land $1M to $15M ACV

Multi-plant OEM and platform fleets standardising on Chassira, with custom weld, paint, geometry and battery models.

  • Multi-plant fleet management
  • Custom weld, paint, geometry and battery models
  • Plant edge fleet with on-prem option
  • Group autonomy policy and approval chains
  • SLAs, SSO and RBAC, dedicated engineer
Contact us
FAQ

Straight answers

The questions plant managers, launch engineers and quality leads ask in the first meeting.

Yes, but only within an explicit tag allow-list with per-tag rate and magnitude limits, inside the qualified envelope, and only at the autonomy level your plant has set. Design partners start in shadow mode, where Chassira writes nothing. Weld-schedule changes wait for a named body-shop engineer, and torque specifications, battery-joint parameters and end-of-line test limits and verdicts are read-only to every agent, always.

Get started

Name the process that costs you the most

Start with one process and one measurable baseline. A paid pilot on body-shop weld and gap-and-flush vision, paint-defect detection and film-build control, or torque and battery-joint conformance shows the number before you commit further.